I got to “back taxi” for the first time today, after landing the first time on 31L I was told to make a 180 turn and taxi back on the runway. I hadn’t done this before, but it went fine. I think I did this after 3 of the landings on 31L. After the fifth landing on 31L I was told to cross 31R and taxi back on taxiway Y and to change back to the usual tower frequency of 119.8. It was really hot in the plane as I taxied back and the sweat was just dripping of me. I made the last takeoff on 31R for right traffic. Had a good trip around right traffic and extended my downwind for another plane coming straight in for 31R. The landing was poor, I flared a little hard, ballooned up, added a little power, but still bumped down a little hard. I figured that it was too hot and I was getting tired so I called it a day and terminated.

So today was about building more confidence in flying solo. The landings were better than yesterday, though still not up to what I was doing flying dual last week. The pattern and radio work is also good. I’m starting to get sick of flying circles around RHV, so it will be nice to get signed off to go down to South County and Hollister tomorrow.

Normal pre-flight, taxi, run-up and take off on 31L with a downwind departure from left traffic. I took off behind a Cessna 152 and followed him South, as I was a bit faster and climbed a bit better we gradually overtook him, he was the only traffic we encountered until Anderson Reservoir. Grainne, tuned into Bay Approach and after initially telling us to stand by, they gave us a transponder code to squawk and started issuing traffic warnings, none of which were much use. Firstly, they never told us about the C152 1000’ below us, and then over Anderson Reservoir another Cessna 172 flew right passed us only 500’ above our altitude. They did however tell us all about the big jets on final approach to San Jose International, none of which were anywhere close to us. However, it was still cool flying along hearing your own plane’s call sign and also listening to all the big planes getting their approach clearances into San Jose. Bay Approach terminated flight following about 12 miles North of Hollister, we had expected them to pass us off to Monterey Approach, but they just told us to squawk 1200, the VFR transponder code, meaning we were back on our own.

I tuned into the Hollister CTAF frequency about 10 miles North of the field and asked for a traffic advisory, one plane replied that he had just taken off into a stiff headwind from runway 24, which is the shorter of the two runways. I had spent some time before hand working out the traffic patterns for the airport as this was my first visit down here, we took a quick review as I started to descend from 3500’. About this time another plane called in from Southeast of the field looking for a traffic advisory, so I passed on the info I’d just got. He said he was just doing a touch and go and entered the left 45 as I crossed the field at 2000’. I did a descending right 270 degree turn which brought me in on the 45 for left downwind. One of the more complicated pattern entries but it worked beautifully. The other plane was just turning base as I entered the downwind and he was already departing when I got onto final. The headwind was really blowing, I kept checking my airspeed which was 65~70 KIAS on short final, but we still seemed to just crawl towards the numbers. I would guess the wind was at l2~15 knots, but at least it didn’t appear to be gusting. The landing was reasonable. I cleared the runway and dropped Grainne off by some hangers. Then taxied off to do two solo landings. These went reasonably well, but the pattern was a bit sloppy, especially trying to keep parallel to the runway. It didn’t feel too bad at the time, but the GPS shows I was angling in towards the runway on both downwind trips. This shortened the base leg, which pretty much made them continuous turns instead of two turns. Another plane landed as I flew the second trip through the pattern. He pretty much just came straight in for the runway. I don’t think your supposed to do this, but at least he told me what he was up to so it wasn’t a surprise. The first landing was good, on the second I ballooned up and had to add some power to keep from dropping back in. I think it looked better from the ground than it did from the plane because Grainne didn‘t seem that upset when I taxied back to pick her up. We took off and made a right crosswind departure, it was real bumpy as I climbed back up to 3000’

Once we got back to cruise altitude Grainne told me it was my choice if I wanted to go to South County, I guess she thought I might be tired, I felt fine so I tuned in South County CTAF and started a descent. There was one plane on the ground saying he had just landed on runway 32, so I planned to fly wide of the field and then make a left turn onto the 45 for right downwind. The pattern entry was good, but something wild happened to the turn onto base. I came out almost passed the end of the runway and so overshoot badly on the turn to final. Then I overcompensated trying to get lined up for final. At this stage I figured this approach was so screwed up I’d just go around and try it again. I really wasn’t sure what had gone wrong, I’ve flown the pattern several times before without problems. I had just climbed back to pattern altitude of 1300’ and made the turn onto crosswind when some guy came on the radio and said he was the FBO (Fixed Base Operator) and that the wind sock was now showing the wind favored runway 14. I was flying the downwind for 32 at this point so I was a little lost as to what to do. I figured I’d take a look at the windsock for myself and then decide. So I said on radio I was going to fly parallel the runway and take a look at the windsock, to which the FBO guy replied, “I can see it from where I’m sitting and it favors 14”, he sounded kind of mad that I didn’t believe him or something. But he’s on the ground and I’m in the plane so I’ll be the one who decides which f**king runway I’m going to land on. The windsock did favor 14 so I made a left 180 degree turn and came in on a very long base leg. The landing was reasonable, and we did the touch and go. Grainne said we’d do a downwind departure and head back for home. There was more interesting radio work on the way out, another plane was coming in from the South, and it was a comedy of errors while he tried to determine what planes were flying, instead of listening to what people were saying he kept asking where people were. Along the lines of “where is the plane in the air?” (I hope he knew there was only one) and “who is still on the ground?”.

I had a pretty uneventful trip back to RHV. Called the tower at 3000’ over UTC and was told to come straight in for 31L. Started a nice stable 90 KIAS descent and the approach went well, though I got changed to 31R at the 3 mile report point. I added the full flaps a little early and so had to add some power coming over the Mall. I even tried a little side slip to account for the minor crosswind (I had too much rudder, but any practice is welcome). The landing bounced once, but recovered in a reasonable fashion - not good though.

So today was fun, a new airport, more solo work that’s really not scary now and some real interesting pattern work at uncontrolled airports. Now I’m endorsed for both Hollister and South County so I have the run of the south practice area on my own. On Wednesday I’ll do an hour of ground work to plan the first cross country flight with Grainne, and we’ll fly it on Saturday. I’ve also signed up for some solo flights on Thursday and Sunday so I’ll head down south and practice some maneuvers and landings.

I had spent about an hour of ground time with Grainne on Wednesday evening to preview the flight planning, we picked out the route and landmarks, measured the leg distances and calculated the headings given an assumed wind. All this using the high tech cardboard E6B flight computer. I also called Oakland Flight Service Station (FSS) and got a standard weather briefing, unfortunately I forgot to tell him I was a student and he rattled through the briefing so quickly I barely wrote down 10% of what he said. Still, I got the feel for what was going on. I studied the ground school CD’s for the cross-country on Thursday night and finally learned how the E6B is really used (I was a bit bemused with what Grainne was telling me the night before). For a child of the computer age, having never even seen a slide-rule I was amazed at how clever the little gadget was - in fact better than the electronic version I’ve been playing with in my Palm Pilot - much more intuitive. For the aviationally challenged an E6B is a rotary slide-rule setup for doing common aviation calculations like “how many minutes to fly 15 miles at a speed of 115 MPH”, or “how much fuel is used in 15 minutes with a burn rate of 8.6 GPH”. The back side also has a very clever method of calculating how the wind effects the direction and speed of flight, for example finding how much headwind or tailwind you have and how it will effect your ground speed and your direction.

On Friday night I setup FS2000 with the current weather conditions, redid the calculations and flew the route on the simulator. This went well though some the landmarks I had picked out were really hard to identify. The fight was great until I crashed on landing at Castle - stupid simulator, doesn‘t it know I can land a real airplane on my own!

So Saturday morning the marine layer fog was a solid overcast when I arrived at the airport at 10am. Grainne and I planned to spend an hour getting the current weather conditions and making the final calculations for the flight plan. This all went well, we started by going through the weather on DUATS which is an online service contracted by the Government to provide pre-flight information. Then I called the FSS again and remembered to tell him I was a student and got a standard briefing. No bad weather once the fog burned off. The guy must have repeated “Don’t go until the fog is gone” about three times. I filed the flight plan over the phone, you can do this by just leaving a recording, pretty cool. In the end we waited until 12:00pm until the sky was clear enough to get going. I finally got to use the kneeboard I bought back in August. I got it after the flight in 8276E which had no side pockets. After that flight I never bothered to use it because it just seemed like overkill and I never flew in 8276E again. Normally, I just have my checklist card, with a small note-pad attached to it with a bull-dog clip and a pen slipped over the top. The knee board is a fancy thing full of pockets that attaches to your knee with a strap and holds all the goodies you need for cross-country flight.

Once I got Castle in sight, I reported I could see it to Stockton Approach and they terminated flight following and told us to squawk 1200 again. I couldn’t raise anyone on the Castle CTAF frequency to find out the runway in use so I over-flew the windsock at 2000’, it seemed to show a crosswind, but slightly favored runway 31. Castle is an old Air Force base, it has an 11,800’ x 300’ runway that can take B52 bombers, you could land five Cessna 172’s in formation on the runway it’s so huge. I started a left 270 degree turn to come in on the right 45 for runway 31 when Grainne pulled the engine to simulate a failure. I made it around the turn though it was a bit messy as I was trying to pitch for best glide at the same time. Didn’t bother with checklists and just headed straight onto the base leg. I was way high coming in over the numbers, but who cares I had 4 time the usual runway to land on. The landing was good. I was worried that the enormous scale of the runway would cause me to mistime the flare, but it didn‘t. Even the center strip painted on the runway was about 4 times wider than I was used to. The place was empty, we saw one Cessna 152 on a taxi way and another plane landed while we taxied back to the start, that was it. I believe there is a cool aviation museum somewhere close by, but we went straight back to the runway to head home.

Grainne had me try my first soft field takeoff which was poor, I didn’t realize just how much forward pressure is needed to keep the plane in ground effect. Still we got off OK. We were just climbing through about 200’ when she pulled the engine again to simulate a failure on take-off - life would be nice is these only happened on 11,800’ runways. I still had half the runway to land on. Got myself configured to land and would have made it easily when Grainne said to go-around, so full power again and flaps back up and we made a crosswind departure. About this time Grainne asked me what I had forgotten in the post-landing checklist - I couldn’t think of anything until she told me. Duh, I had forgotten to close my flight plan - if you don’t close it they fear the worst and come looking for you. Grainne took care of this as we climbed back up to 4,500’. It was a bit finicky, you have to transmit on one frequency on the radio and listen on another frequency on the navigation radio for the reply, it took a couple of tries but she finally got it to work.

On the way back we used radio navigation as opposed to the pilotage and dead reckoning we used on the way out. We intercepted the 260 degree radial on the Merced VOR (a special type of transmitter that sends radiating spokes of signals out in all directions). This radial gave us a straight line course back to Mt. Hamilton. The ride back was nice, but really started to get bumpy over the top of the mountains. Mt. Hamilton is 4,200’ high, I was really quite nervous flying over at just 4,500’ so I let the altitude creep up to 4,700’ as we crossed over. The view of the lick observatory was spectacular. We got the current ATIS and I called into Reid Hillview Tower, they told me to enter on right base for 31R and report two miles. I started descending, but this is tricky on this approach to RHV. The mountains drop away very steeply just about 4 miles east of the field, so even if you just clear the last ridge line you are still way too high to land. So we did a forward slip to loose the altitude - which once again went poorly. Grainne had to help me get into the slip and the plane was yawing every which way. Still we got down and I was cleared to land on 31R when I reported in at 2 miles. The landing was fine. Today was a really fun flight and I’m looking forward to more cross-counties.

Did my first pre-flight in the dark with a flashlight, it took a bit longer but was otherwise OK. The panel lighting in 4754D is great, much better than 5766J (in fact now that I have the radio thing fixed, 54D is becoming my favorite plane). We had some fun with the radios, but this time it wasn’t us. It was the tower. When we tuned into Ground Control there was a really loud buzzing sound. Grainne called the tower and told them about it, at which time another plane chimed in said they had the same problem. So we were cleared to taxi down Zulu while the tower guys figured out there problem, helping them with various radio checks along the way. Finally about halfway down they got it working and thanked us for our help and then asked us what our departure request was. We told them and got a transponder code just before the run-up area. Had a normal run-up and did a straight out departure running along the east side of I-680 to stay out of class C.

We were cleared to change frequency to call SJC Tower just about the time I leveled off at 1500’. They asked for our altitude and for an IDENT on our transponder and then confirmed radar contact. As expected we were told to over fly the field at or above 1500’ and enter left downwind for runway 29. Right about this time I realized there was a cloud right off my right side and as I turned towards SJC we hit the bottom of the ceiling, I started descending and was at about 1400’ as we got close to the field. I was kind of worried about the clouds and being lower than instructed (though Grainne pointed out that the transponder was still showing 1500’ which is what the tower would see). In the confusion I was cleared to land as I passed over the center of the field, and I repeated back that clearance. I went out quite far beyond the field to make sure I had plenty of time to descend to pattern altitude and get established on the 45. A left 180 degree turn brought me in on the 45 at 1000’ and I turned downwind. It was kind of hard to make where the end of the runway was in order to judge the turn to base leg and of course this time I didn’t have any familiar ground references. Just about this time the Tower said, “Be advised traffic on final for the parallel runway is a Boeing 757”, this was pretty cool, I’m used to getting traffic alerts for rather smaller planes. The 757 was a lot easier to see than the usual Cessna’s and whatnot around the RHV traffic pattern. I made the turn from base to final early and angled onto the final approach trying to stay as far away as possible from the big iron landing on the runway next door. The final approach and landing went pretty well and Grainne called for a touch and go. As we climbed out the tower asked where we were and I said we had done a touch and go. At this point we realized that we only had a clearance for a landing not for the option (to do the touch and go). Tower asked us what we wanted to do, we decided that with the ceiling coming down fast at SJC and having just pissed the Tower guys off we’d better get out of Dodge, so we told them we would go back to RHV. They said, “make an immediate left turn and cross the field at 1500’”. Of course, the ceiling had dropped some more and I only got to about 1350’ before we hit the clouds. Grainne called the Tower and told them we could only maintain 1350’ crossing the field, they didn’t seem to mind and were probably just glad we were leaving before we screwed anything else up. A little passed the field they told us radar service was terminated, to squawk 1200 and contact RHV. So ended my first foray into class C airspace.

It took a couple of tries but the Tower at RHV finally answered and gave us the option of left or right traffic, I’d pretty much reached I-680 at this point so right traffic for 31R made the most sense. We did five landings and they were a lot of fun. The first was normal and went well. The second time around Grainne pulled the engine about mid downwind and I did a dead stick landing that worked great. Grainne’s only quibble was that I used 40 degrees of flaps to get down. I had shortened the downwind to make the final leg intentionally short and high. I wanted to land about a third of the way down the runway and I figured “altitude is options” so better high than low. As I was plenty high I needed all the flaps to get down. Grainne’s point was the plane is harder to control with full flaps and no engine, but at least I got down. On the third time around we were going to practice a forward slip. Grainne told me to take the engine to idle and pitch for 70 KIAS abeam the numbers. I’m not sure what she was intending. I extended the downwind a little, but of course we were descending faster than usual so we ended up on glide slope as I turned onto final (even without any flaps). So no need for a slip as it is used to lose unwanted altitude without gaining speed and we didn’t have any unwanted altitude at that point. Grainne had me do a no-flap landing instead, basically the same as a normal landing but the nose is pitched quite a bit higher. The landing was fine. The next time around there was a plane coming in on final approach so we had to extend our downwind a little bit anyway. I just kept at pattern altitude but slowed to about 70 KIAS on base. So of course we were high and long as we turned onto final - exactly what I wanted to practice the slip. For the first time I got into the forward slip, held the center line of the runway perfectly, lost exactly the altitude I wanted and exited without a flaw. It was great, I’ve had problems with this maneuver every time I’ve tried it until now. The actual landing went fine after than. On the last time through Grainne pulled the power again. This time I turned a little too early and ended up much higher than I wanted, I also resisted putting in the last 10 degrees of flaps so we were staring to run out of runway. Grainne said to pitch down for a speed of 80 KIAS to get down quicker. We got down with the end of the runway rather close to us, Grainne said “lets try to stop without running off the end”, I don’t know why she was worried, we stopped without problems and terminated for the night.

Tonight was a lot of fun. Landing at San Jose was a blast. Skimming along just under the clouds we cool and the landings as RHV went pretty well. Not just basics to get in the requirement for 10 night landings, but a chance to practice the dead-stick and slips as well. Next Thursday is scheduled for another solo flight but the weather looks iffy. On Saturday we’ll do the long cross country, we’re going to Pine Mountain Lake which is at just under 3000’ a little Northwest of Yosemite Valley.

I made a dumb rookie mistake that I’ve never made before, I forgot to call Ground Control before starting to taxi - I was just about to go when Yoed says “Are you just going to start?”, then I realized what I had done - oh well, maybe I should write that one in on my checklist. We had a normal run-up and takeoff from 31L. I was just about the call the Tower when they told me to expedite crossing 31R and takeoff. That break in routine caused me to make my second rookie mistake - I forgot to turn on the transponder and landing light (the usual “lights, camera, action” checklist just before takeoff). From now on I’m going to just turn them on at the end of the run-up unless there’s a long line of planes waiting to takeoff (meaning I’ll have time to remember it then).

We proceed to do 7 takeoffs and landings. All the takeoffs were a combo soft & short technique. Basically, holding the nose wheel off the runway and then flying in ground effect to build speed, then climbing at best angle of climb to simulate clearing an obstacle at the end of the runway. Yoed made a good point, many soft fields are also short so its not unusual to have to combine the techniques. The first few takeoffs were a little ragged with a lot of drift sideways flying in ground effect. Yoed really drilled me on keeping the center line during the takeoff - more right rudder and use the ailerons. This paid off and the last couple of takeoffs were right down the line. Of the seven landings, two were soft-field and the rest were short field. I really had fun with the short field landings. 40 degrees of flaps brings you in steep, the flare is very positive and you really try to plant your wheels on the aiming spot. Two of the landings were my best ever, I aimed for the numbers and planted the mains right down on them, not hard, but just firmly enough that you knew you had arrived. Yoed commented that one was “commercial standard” whatever that means. We only had one go-around, I’m still not sure what went wrong. I believe, I was a little fast and I started to flare early and too much. So I ended up about 15’ above the ground and then started to just drop in. Yoed called for power and then a go around. He seemed real concerned which bothers me because I think I would have still attempted the landing (with just adding power to soften the landing). I’m not sure what exactly I missed that made it so bad. The two soft-field landings were a mixed bag, one was reasonable, the other felt more like a normal landing - I will have to practice these more.

Tonight was fun, Yoed is always nice to fly with - he’s precise and picks up on a lot of little stuff that Grainne lets slide. He’d probably drive me nuts if I flew with him every time, but great for a brush up on technique.

A normal takeoff and as we climbed towards Calaveras Reservoir I called Oakland Flight Service Station and opened the flight plan, the guy was real nice, he needed to get my name, I guess the recorded message I left when I filed the plan garbled my it and he gave us a frequency for filing pilot reports (PIREPS) and position updates during the journey. We were just leveled off at 4500’ when I called Bay Approach to request flight following. I completely screwed it up, I forgot to tell him where I was, how high I was and what I wanted and I think I forgot to repeat my call-sign a couple of times. In the end he just gave me another frequency to call. I was completely flustered. I started from scratch on the new frequency and thankfully got it right this time - I’m still intimidated by talking to Bay Approach along with all the “real” air traffic in the congested Bay Area. The sequence is not hard, basically you initiate the call with “Bay Approach, Skyhawk 5766J, request”, then wait for them to reply usually with “Skyhawk 5766J, Bay Approach state you request”. Then you tell them where you are and what you want, “Bay Approach, Skyhawk 5766J, 10 miles North of Reid-Hillview, 4,500 feet, request flight following from Reid-Hillview to Pine Mountain Lake”. They then give you a transponder code to squawk, “Skyhawk 5766J, Squawk 0433 and IDENT”. You have to repeat the code back to them to make sure you got it right, “0433, 5766J”, enter it in the transponder and push the IDENT button, this will make it flash on their radar screen so they can pick it out easily. After that they will come back and confirm radar contact, “Skyhawk 5766J, radar contact at 12 miles north of Reid-Hillview, 4,600 feet” and they might ask you to confirm the altitude, “confirm altitude 4,600 feet” to which you reply “Affirmative, 4,600 feet, 5766J”. So you see, a piece of cake really. I was happily heading toward Livermore when they told me I was cleared to climb to 5500’ at my discretion and after that I didn’t hear from them until I was handed off to Stockton Approach somewhere over the Altamont Pass.

The flight went well out to Tracy, I was just a little south of my course at the intersection of I-205 and I-5. The next checkpoint was an intersection of a road and some power lines just outside Oakdale and we hit that one more or less on time. I missed the next checkpoint, it was supposed to be a intersection of a road and a railway, but I never saw it for sure. By this time I knew I was getting fairly close to Pine Mountain Lake, but I was not exactly sure where I was. Finally, I found a bridge that was unmistakable and would have been a much better checkpoint in the first place. Right then I realized that I knew just where I was, the road running across the bridge was highway 120 which is basically the route to Yosemite and I’ve driven it many times, there is a big hydro-electric plant close by that was easy to pick-out near a place called Priests Grade, that’s an incredibly steep hill that worth driving up, but will burn your brakes driving down (I know I’ve done it). Right about this time I saw the airport.

I was a little south of the field so as I descended I flew across it to enter on the downwind leg. I then proceeded to completely screw up the pattern entry. I flew way too close on the downwind, overshot a lot on the turn to final and decided to go around. As I climbed out two planes entered the downwind leg ahead of me so I was now number 3 to land. The wind was brutal, a lot of turbulence and it seemed to be coming from rapidly changing directions. I overshot final again and did another go around. This time Grainne started to talk me through the landing. Third time it worked, the approach was much better. We were just about 50 feet above the ground and for some reason the plane was just floating even with 40 degrees of flaps, suddenly the bottom dropped out and we headed for the ground fast. The flare worked and the actual landing was reasonable. We must have hit some kind of updraft followed by a downdraft just above the ground, it was no fun whatsoever.

Pine Mountain Lake is a “fly-in” community. People actually have houses right next to the taxiways and hangers instead of garages. We taxied to the transient parking and got out to stretch out legs. Grainne once again had to remind me to close my flight plan, which I did by phone. A few minutes on the ground and we decided to head back. Grainne had me do one more loop of the pattern and another landing to make sure I could be more consistent at an unfamiliar airport and to give me a confidence boast that the first landing wasn’t a fluke. The second landing was fine and we did a touch and go. This was probably a mistake because the altitude made the climb out much closer to the trees than either of us would have liked. We departed straight out and I had little trouble picking up the 251degree radial from the Manteca VOR. The air however was really bumpy, the worst turbulence I’ve been in so far, though Grainne said it was only “light”. Once we were back at altitude Grainne had me put on the foggles and I flew on instruments tracking the VOR. This was only hard because of the bouncing around and I did a passable job of staying on course. Of course, once I took the foggles off I had no idea of where I was, other than on the radial so Grainne picked the perfect time to decide to divert me to Lodi. Whether by design or accident Lodi happened to be right on the fold of the map, with the airport on one side and all the associated information on the other. The plane was bouncing around and taking most of my attention to keep it straight and level and I was trying to plot a course to the new airport. The first problem was I didn’t know where I was. I tried triangulating with the Linden VOR and got a rough idea, close enough to very roughly get a course of 285 degrees. Grainne suggested I use the DME (Distance Measurement Equipment) to get the distance to the Manteca VOR, thankfully this agreed fairly closely with my first estimate. Once I’d decided that about 280 was reasonable Grainne had me calculate the ETE (Estimated Time Enroute), the ETA (Estimated Time of Arrival) and the fuel required. Once that was done, I just set the GOTO on my GPS and it gave me a heading of 270 degrees and an ETA that matched mine to the minute (by luck I think).

Actually finding the airport turned out to be a little difficult, there were two airports marked close together on the chart, I could see one below me, but I couldn’t see the other so I wasn‘t sure if I had the right one or not. The ETA (and the GPS) were telling me I’d was over the right airport so I decided to descend and get a better look. I did a descending right turn and as I came around I saw the second airport confirming that I was in fact over the right place, Kingdon Airport. I did a thankfully uneventful entry into left downwind and made a fine landing. There were no taxiways, so we just turned around at the far end of the runway and took off again - there was really no significant wind to force us to take off in any particular direction. We did a crosswind departure which was basically towards home and Grainne told me to just find the fastest way back to RHV.

I could see Mt Diablo in the distance. Reid-Hillview was too far to come up on the “nearest” list on my GPS, but Livermore did so I set that as my destination. I’m pretty familiar with the central valley around Stockton and Tracy so it was easy to set myself up in the right direction. Coming over the Altamont Pass again I could see Mission Peak in the distance, Calaveras Reservoir is right in front so we just made a beeline for familiar airspace. I tried to get a radial from the San Jose VOR, but the mountains got in the way and I didn’t really need it anyway. I got the RHV ATIS and called into the tower over Calaveras. We did a completely standard approach to right traffic for runway 31R though my attempt at a soft-field landing left a lot to be desired.

The trip was fun, though somewhat tiring, almost 3 hours flying and over 200 nm traveled. Other than the problems landing at Pine Mountain Lake it was a good experience. I really didn’t screw anything up badly. I think once I get some more local solo experience I’ll be more than ready to attempt one of these trips on my own.

The oral test went well. We started with the route I’d picked out which was basically a straight line from RHV to FAT. Todd had a problem with simply flying over the mountains to the east of San Jose, firstly would the plane climb fast enough to clear the 3500’ peaks and the fact that there is no place to land if the engine quits. He would have chosen to fly south to Frazier Lake and then follow highway 152 into the central valley. He asked me various questions about the airspace along the route, how I’d get information on weather, how I’d find the frequency for Air Traffic Control. He had a bunch of what if questions, like “What if you’re at Los Banos and Oakland Radio tells you that the Bay Area is fogged in from Oakland to Hollister, good night”, answer go land somewhere like Merced and stay the night. We went through the Sectional making sure I could read the airport information, VOR info etc. The test was supposed to take two hours, we finished in a little over one. The plane wasn’t back so we just chatted while we waited for it to arrive.

The pre-flight and taxi went well, I didn’t forget anything. I had some problems with the run-up, the left magneto was really rough. Like I’d been shown I ran the engine up to 2200 RPM for 10 seconds to burn off any carbon deposits, when that didn’t work I tried full power for 20 seconds. That still didn’t work so Todd showed me a trick, you lean the engine (adjusting the mixture to get max RPM) and then let it run there for about 30 seconds. This makes it run hot - its not recommended but better than grounding the plane for a bad magneto when in fact the plugs are just a little fouled. This did the trick and we were ready for takeoff. I did a fine short field takeoff and downwind departure.

The first checkpoint was the Top of Climb, we hit it 2 minutes late, but within the spec. (inside 5 minutes) and leveled off at 5500’. I established the plane in cruise and finished the checklist and then got the Salinas VOR tuned in and identified as I planned to use a radial to confirm my next checkpoint. At this point Todd tells me to divert to Salinas - I’m thinking this is too easy, I’ve just setup the VOR so the DME (Distance Measuring Equipment) will tell me the distance and time to the VOR for free. Todd realizes this just about the same time I do and says, “Wait, Salinas